🚜 SAME EXPLORER 115 故障代碼整合大全
整合引擎 (E)、變速箱/PTO (T) 與儀錶板 (I) 警報，供團隊快速搜尋及排查。
| 標準化代碼 (E/T/I) | SPN | FMI | 故障描述 (Description / Fault) | 解決方式 / ECU 行動 (Controls / ECU Action) | 嚴重性 |
|---|---|---|---|---|---|
| 🚨 引擎 ECU 警報 (E-代碼) - 依 P/N (Pin/Warning No.) 閃爍次數 | |||||
| E-1 | N/A | N/A | 超速警報Overspeed (Rpm > 3200) | 作動器命令訊號消失 / 重啟引擎Actuator command signal absent / Restart engine | N/A |
| E-2 | N/A | N/A | 作動器開路 (O.C.) 或短路 (S.C.)Actuator O.C. / S.C. (未連接, 線束錯誤 Pin 2-15) | 作動器命令訊號消失 / 重啟引擎Actuator command signal absent / Restart engine | N/A |
| E-3 | N/A | N/A | 油門踏板短路 (S.C.) 或開路 (O.C.)Accel. pedal S.C. / O.C. (電位計短路/未連接, 線束錯誤 Pin 4-9) | 失去油門踏板功能Lost throttle pedal function | N/A |
| E-4 | N/A | N/A | RPM 訊號開路 (O.C.) 或間歇性故障Signal. RPM O.C. / interm. (Pick-up 斷開/故障, Pin 10) | 作動器命令訊號消失 / 重啟引擎Actuator command signal absent / Restart engine | N/A |
| E-5 | N/A | N/A | EEPROM 錯誤 (參數超出範圍, 引擎未校準, 電子單元故障)Eeprom error (Parameters out of range / Engine not calibrated) | 失去功能 (重新編程/校準引擎)Lost function | N/A |
| E-6 | N/A | N/A | 輪速傳感器開路 (O.C.) 或間歇性故障Speed Sensor O.C. / Interm. (傳感器斷開/故障, Pin 8) | 速度限制Speed limiting | N/A |
| E-8 | N/A | N/A | 手油門短路 (S.C.) 或開路 (O.C.)Hand throttle S.C. / O.C. (短路/斷開, 線束錯誤 Pin 6) | 失去手油門功能Lost hand throttle function | N/A |
| E-9 | N/A | N/A | SV 鎖定/電磁閥開路/短路故障SV lockout / L/H SV O.C. / S.C. (SV 繼電器故障, SV未連接/短路) | 失去 HRT/HL SV / L/H SV 功能Lost HRT and HL SV / Lost L/H SV function | N/A |
| E-10 | N/A | N/A | 第二速度傳感器故障/開路Speed sens. 2 interm. / O.C. (傳感器故障/斷開, Pin 12) | 引擎速度限制Engine speed limiting | N/A |
| E-11 | N/A | N/A | 速度傳感器配置錯誤Incorrect Speed Sens. config / incongruent (速度限制不正確, 檢查 Pin 11/12) | 引擎速度限制 (重新配置)Engine speed limiting | N/A |
| E-13 | N/A | N/A | 頂桿電磁閥 (Tappet SV/HRT) 開路/短路或邏輯錯誤HRT SV O.C. / S.C. / lockout / logic states (SV 未連接/短路, Pin 55/64) | 失去 HRT/HL SV 功能 / 引擎速度限制Lost HRT and HL SV function / Engine speed limiting | N/A |
| E-14 | N/A | N/A | 速度讀取或限制配置錯誤Speed reading & Limiting config. error / Inconsistency of limits (需配置限速器) | 引擎速度限制在 1800 rpmEngine speed limiting at 1800 rpm | N/A |
| ⚙️ 變速箱/PTO ECU 警報 (T-代碼) - 儀錶板顯示代碼 | |||||
| T-8 | 5562 | 13 | 檔位配置錯誤Gear configuration error | 檢查變速箱配置Check the correct gearbox configuration | Low |
| T-9 | 5561 | 13 | 機器設定未完成Commissioning not completed | 執行機器設定Commission the machine | High |
| T-10 | 5560 | 13 | 離合器或 Stop&Go 未校準Clutches or Stop&Go not calibrated | 校準梭式換向Calibrate the shuttle | Low |
| T-11 | 5562 | 13 | 油門踏板和手油門未校準Throttle pedal and hand throttle not calibrated | 校準加速器Calibrate the accelerators | Low |
| T-12 | 177 | 3 | 溫度傳感器斷開或短路至 12VTemperature sensor disconnected or short circuit to 12V | 檢查線束、傳感器、傳感器供電級Check wiring loom, the sensor, sensor supply stage | Medium |
| T-13 | 177 | 4 | 溫度傳感器短路至接地 (earth)Temperature sensor short circuit to earth | 檢查線束、傳感器、傳感器供電級Check wiring loom, the sensor, sensor supply stage | Medium |
| T-15 | 1504 | 4 | 座椅傳感器斷開或短路至 GNDSeat sensor disconnected or short circuit to GND | 檢查線束、傳感器、傳感器供電級Check wiring loom, the sensor, sensor supply stage | Low |
| T-16 | 1504 | 3 | 座椅傳感器短路至 12VSeat sensor short circuit to 12V | 檢查線束、傳感器、傳感器供電級Check wiring loom, the sensor, sensor supply stage | Low |
| T-17 | 1504 | 2 | 座椅傳感器 (訊號級別無效)Seat sensor (signal level invalid) | 檢查線束、傳感器、傳感器供電級Check wiring loom, the sensor, sensor supply stage | Low |
| T-18 | 127 | 2 | 服務壓力開關，合理性錯誤Services pressure switch, plausibility error | **文件丟失檢查方式** | Low |
| T-19 | 123 | 2 | 比例閥壓力開關合理性錯誤 (閥門開啟但無壓力)Proportional valve pressure switch plausibility error (valve open but no pressure) | **文件丟失檢查方式** | Low |
| T-20 | 123 | 3 | 比例閥壓力開關合理性錯誤 (閥門關閉但有壓力)Proportional valve pressure switch plausibility error (valve off but pressure present) | 檢查 4 Bar 壓力開關線束、開關、比例閥是否有機械卡滯Check 4 Bar pressure switch wiring loom, switch, check for mechanical jamming of proportional valve | Low |
| T-24 | 5222 | 2 | 離合器打滑過度Excessive clutch slipping | 檢查離合器打滑的原因Check cause of clutch slippage | High |
| T-25 | 5223 | 2 | 交流發電機皮帶打滑Alternator belt slipping | **文件丟失檢查方式** | Low |
| T-42 | N/A | N/A | 儀錶板與變速箱 ECU 之間的 CAN 網路故障Fault relative to CAN network between cluster and transmission ECU | 檢查線束、檢查 TCU 保險絲Check wiring loom, Check the TCU fuse | Low |
| T-47 | 191 | 12 | 輪速傳感器斷開連接Wheel speed sensor disconnected | 檢查線束、檢查傳感器、檢查傳感器供電Check wiring loom, the sensor, sensor supply | Low |
| T-48 | 191 | 3 | 輪速傳感器短路至 12VWheel speed sensor short circuit to 12V | 檢查線束、檢查傳感器、檢查傳感器供電Check wiring loom, the sensor, sensor supply | Low |
| T-50 | 160 | 12 | 梭式換向輸出速度傳感器斷開連接Shuttle output speed sensor disconnected | 檢查線束、檢查傳感器、檢查傳感器供電Check wiring loom, the sensor, sensor supply | Low |
| T-51 | 160 | 3 | 梭式換向輸出速度傳感器短路至 GND 或 12VShuttle output speed sensor short circuit to GND or 12V | 檢查線束、檢查傳感器、檢查傳感器供電Check wiring loom, the sensor, sensor supply | Low |
| T-52 | 160 | 2 | 梭式換向輸出速度傳感器合理性錯誤Plausibility error on shuttle output speed sensor (valve controlled but speed zero) | **文件丟失檢查方式** | Low |
| T-64 | 598 | 2 | 離合器踏板電位計合理性錯誤Plausibility error on clutch pedal potentiometer | 檢查線束、傳感器、供電和安裝Check wiring loom, the sensor, sensor supply Check sensor installation | Low |
| T-65 | 5110 | 4 | 離合器踏板電位計斷開或短路至 GNDClutch pedal potentiometer disconnected or short circuit to GND | 檢查線束、傳感器、供電和安裝Check wiring loom, the sensor, sensor supply Check sensor installation | High |
| T-66 | 5110 | 3 | 離合器踏板電位計短路至 +12VClutch pedal potentiometer short circuit to +12V | 檢查線束、傳感器、供電和安裝Check wiring loom, the sensor, sensor supply Check sensor installation | High |
| T-67 | 1079 | 2 | 5V 傳感器電源故障5V sensor power fault | 檢查引腳 14 的電源、檢查所有 5V 供電傳感器的線束和連接Check the power supply to pin 14, Check wiring loom and connections of sensors powered with 5V voltage | High |
| T-70 | 5110 | 13 | 離合器踏板電位計校準數據不正確Clutch pedal potentiometer incorrect calibration data | 關閉/開啟點火開關，然後重複踏板校準程序Ignition switch off/on, then repeat the pedal calibration procedure | High |
| T-73 | 5130 | 4 | 舒適離合器按鈕合理性錯誤Plausibility error on Comfort clutch button | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-74 | 5130 | 3 | 舒適離合器按鈕短路至 +12VComfort clutch button short circuit to +12V | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-86 | 5215 | 4 | 手動離合器按鈕斷開或短路至 GNDManual clutch button disconnected or short circuit to GND | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-87 | 5215 | 3 | 手動離合器按鈕短路至 +12VManual clutch button short circuit to +12V | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-90 | 5130 | 2 | 舒適離合器按鈕合理性錯誤Plausibility error on Comfort clutch button | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-91 | 5130 | 12 | 舒適離合器按鈕斷開連接Comfort clutch button disconnected | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-95 | 5215 | 2 | 手動離合器按鈕合理性錯誤Plausibility error on Manual clutch button | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-96 | 5215 | 12 | 手動離合器按鈕斷開連接Manual clutch button disconnected | 檢查線束、檢查按鈕Check wiring loom, Check the button | Low |
| T-100 | 5140 | 2 | 梭式換向電位計合理性錯誤Plausibility error on shuttle potentiometer | 檢查線束、傳感器、供電和安裝Check wiring loom, the sensor, sensor supply Check sensor installation | High |
| T-101 | 5140 | 4 | 梭式換向電位計斷開或短路至 GNDShuttle potentiometer disconnected or short circuit to GND | 檢查線束、傳感器、供電和安裝Check wiring loom, the sensor, sensor supply Check sensor installation | High |
| T-102 | 5140 | 3 | 梭式換向電位計短路至 +12VShuttle potentiometer short circuit to +12V | 檢查線束、傳感器、供電和安裝Check wiring loom, the sensor, sensor supply Check sensor installation | High |
| T-103 | 5140 | 13 | 梭式換向電位計校準數據不正確Shuttle potentiometer incorrect calibration data | 關閉/開啟點火開關，然後重複校準程序Ignition switch off/on, then repeat the calibration procedure | High |
| T-106 | 177 | 0 | 溫度過高 (> 115°C)Temperature too high (> 115°C) | 發出聲音警報、變速箱油門限制在 50%、檢查冷卻系統Acoustic alarm, G/B throttle limited at 50%, Check cooling system | Medium |
| T-107 | 177 | 1 | 溫度過高 (110°C)Temperature too high (110°C) | 發出聲音警報、變速箱油門限制在 50%、檢查冷卻系統Acoustic alarm, G/B throttle limited at 50%, Check cooling system | Medium |
| T141 | 51 | 12 | 油門踏板電位器故障或斷開Temperature too high (110°C) | 檢查油門踏板電位器線束，檢查電位器Acoustic alarm, G/B throttle limited at 50%, Check cooling system | Medium |
| T142 | N/A | 12 | 手油門電位器故障或斷開Fault relative to CAN network between cluster and transmission ECU | 檢查手油門電位器線束，檢查電位器Check wiring loom, Check the TCU fuse | Low |
| T143 | N/A | 12 | 儀錶板與變速箱 ECU 之間的 CAN 網路故障Fault relative to CAN network between cluster and transmission ECU | 檢查線束、檢查 TCU 保險絲Check wiring loom, Check the TCU fuse | Low |
| 📟 儀錶板 ECU 警報 (I-代碼) - 儀錶板顯示代碼 | |||||
| I18 | 20-5K | 4 | 溫度傳感器短路至接地Temperature sensor short circuit to earth | N/A | Low |
| I19 | 20-5K | 3 | 溫度傳感器電源短路Temperature sensor power supply short circuit | N/A | Low |
| I20 | 21-5K | 3 | 燃油液位傳感器短路至電池Fuel level sensor short circuit to battery | N/A | Low |
| I21 | 24-5K | 12 | 頻率傳感器 1 未連接 (引擎 RPM)Frequency sensor 1 not connected (Engine RPM) | N/A | Low |
| I22 | N/A | 12 | 頻率傳感器 2 未連接Frequency sensor 2 not connected | N/A | Low |
| I23 | 19-5K | 12 | 預熱繼電器命令訊號 - 功率輸出 0 斷開連接Preheat relay command signal - Power output 0 disconnected | N/A | Low |
| I24 | 19-5K | 4 | 預熱繼電器命令訊號 - 功率輸出 0 短路至接地Preheat relay command signal - Power output 0 short circuit to earth | N/A | Low |
| I25 | 19-5K | 3 | 預熱繼電器命令訊號 - 功率輸出 0 短路至電池Preheat relay command signal - Power output 0 short circuit to battery | N/A | Low |
| I26 | 19-5K | 2 | 預熱繼電器命令訊號 - 功率輸出 0 短路至電池或開路Preheat relay command signal - Power output 0 short circuit to battery or open circuit | N/A | Low |
| I36 | N/A | 3 | 預熱繼電器短路Preheating relay short circuit (preheating function) | N/A | Medium |
| I37 | N/A | 13 | 預熱繼電器故障Preheating relay faulty (preheating function) | N/A | Low |
| I38 | 18-5K | 4 | 座椅傳感器短路至接地Seat sensor S.C. to earth | N/A | Medium |